September 11, 2019 posted by

LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.

Author: Shaktizragore Nejar
Country: Australia
Language: English (Spanish)
Genre: Automotive
Published (Last): 9 December 2005
Pages: 140
PDF File Size: 7.11 Mb
ePub File Size: 5.36 Mb
ISBN: 515-3-68697-986-6
Downloads: 36601
Price: Free* [*Free Regsitration Required]
Uploader: Tazragore

These limits are not to be used to calculate outgoing quality datasbeet. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. The capacitor used should be a low-leakage type.

A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0. The LM also provides excellent stability vs. Consult factory for availability of devices with Guaranteed Long-term Stability.

Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. National Semiconductor Europe Fax: The curves showing the Noise vs. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. The device does not include a thermal shut-down circuit. Consult factory for availability of devices with tighter Accuracy and Tempco Specifications. They are based on a buried zener reference as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending.

A military RETS electrical test specification is available on request. In some applications it may be advantageous to pre-load the output to either Vin or to ground, to avoid this crossover point.


LM607 Datasheet

The LM is suitable for limited-temperature operation. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use datasheey in the labeling, can be reasonably expected datashwet result in a significant injury to the user. Do not connect anything to these pins, or improper operation may result. However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature.

There is dstasheet guarantee that the Specified Temperatures are exactly at the minimum or maximum datasbeet. Thermal regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW. The LM has a Class B output, and will exhibit transients at the crossover point. Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Tempco linearity at temperature extremes.

Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Tempco. Regulation is measured at constant temperature using pulse testing with a low duty cycle.

If the output is pulled to a positive voltage such datsaheet a 15 or a 20V, the output current will be limited, but overheating may occur. LM see curve above: Pin numbers for H, M or N packages.

LMA datasheet & applicatoin notes – Datasheet Archive

For example, if the output were trimmed up to Contact the factory for availability of devices with proven long-term stability. The LM is recommended datasheeet applications where the highest stability and lowest noise is required over the full military temperature range. These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output.


The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. Documents Flashcards Grammar checker.

LM607 PDF Datasheet浏览和下载

Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise. Avoid such overloads for voltages higher than a 20 V, for more than 5 seconds, or, at high ambient temperatures. These pins may be cut off if desired. The output is short-circuit-proof to ground.

To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground. Capacitance in the Typical Performance Characteristics section show graphically that a modest capacitance of 0. The output can sink current as well as source it, but the output impedance is much better for sourcing current.

Dtaasheet, Kowloon Hong Kong Tel: The trim pin pin 5 should also be guarded away from xatasheet signals and leakages, datasyeet it has a sensitivity datasheef 15 millivolts of DVout per microampere.

The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area.

This datasheet has been downloaded from: Unless otherwise noted, these conditions apply: In Sinking mode, connect 0. Alternatively, a shield foil datasheet be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively acting as a guard against AC coupling and DC leakages. This point occurs when the device is required to sink approximately 1. The devices have a