September 15, 2019 posted by

Product data sheet. Rev. 03 — 19 December 2 of Philips Semiconductors. 74HC; 74HCT 8-channel analog multiplexer/. HC Datasheet, HC PDF, HC Data sheet, HC manual, HC pdf, HC, datenblatt, Electronics HC, alldatasheet, free, datasheet. s Digital multiplexing and demultiplexing s Signal gating. 74HC; 74HCT 8-channel analog multiplexer/demultiplexer. Product data sheet.

Author: Shakasa Danris
Country: Fiji
Language: English (Spanish)
Genre: Environment
Published (Last): 2 February 2007
Pages: 370
PDF File Size: 8.21 Mb
ePub File Size: 12.64 Mb
ISBN: 281-9-37180-317-8
Downloads: 72369
Price: Free* [*Free Regsitration Required]
Uploader: Mezigis

HC datasheet, HC datasheets, manuals for HC electornic semiconductor part

Related Hardware and Initiatives. Message 10 of Message 1 of Sources for Electronic Parts. Message 7 of The only difference will be the EN signal as it will still be active high instead of active low. But you can read and write to the pins quite fast. Could you please clarify which one it actually is?

Futhermore, the is able to work with analog values; in the case of the Arduino, you are able to use the analog inputs with a voltage between V and route them to an Analog-In Pin on your Arduino.

Can I take the model and write it to a. Message 9 of If I have misunderstood please forgive me.

What have I done wrong please? I did try save the model as a. If this model is fairly close to what you need then instead of dztasheet the model try editing the symbol to reflect the pin names you require. I know that it can be frustrating when the component you need is not there. A multiplexer or demultiplexer enables you to expand the in-and outputs on your Arduino board.


What is far more bothering is scoping the output at Z shows only 1. You can get the datasheet from their website and then use the ‘New H4051 Wizard’ to create it. I think I see why the output may be very low perhaps – I put a 10K resistor between the output and ground and the output vanished. Message 5 of Board Setup and Configuration.

Message 8 of You can just cut a paste hc40551 into Notepad or some other text editor and edit it that way.

【HC4051 MFG】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

There is ddatasheet delay needed between selecting and read datasjeet writing the pin. I don’t think that anyone has created this component in the past. Here it is with the hc401 name corrected and also with a correction to the Mux Input selection switches bit, which I initially hoped was what my problem was, but it is still not working.

So my guess is that the switch isn’t switching. I tried to work out how to modify an exisiting model ADGFbut failed miserably, as I’m not able to infer the language syntax from the model hv4051 unlike the digital models which I could work out, albeit slowly. Message 4 bc4051 Another idea would be to use the datxsheet model.

So that clearly doesn’t fly as an option: You can choose between 8 different inputs and select just one you want to read at the time. Here’s an alternative idea that might help. If you use the as a Multiplexer: If you use the as a Demultiplexer you can choose between 8 different outputs and select just one you want to write at the time.


The main differences are. Kittmaster’s Component Database http: Message 3 of Also, in your original post you said the IC was 74hc, but the model file you posted says 74hc Message 6 of An alternative approch might be to hack the model for the 74HC, but again, I wouldn’t know quite where to start!

Has anyone created a model for this analogue mux? With this configuration on an IC it really makes no difference as to what they are called so you can edit the symbol and call it what you want i.

Most Active Software Boards: I created a very simple no attempt to model delays or capacitive loading model which I think ought to work, but it behaves slightly oddly. This will still require an inverter to create the proper logic signals you need. It is not possible to read or write more than one pin on the at the same time, because you can only select one pin at a time.

The playground is a publicly-editable wiki about Arduino.

How can I debug this please? For more info pleae look at this Forum Post.

【HC MFG】Electronic Components In Stock Suppliers in 【Price】【цена】【Datasheet PDF】USA

Each of these pins have to be connected to one digital out pin on the Arduino. As far as the voltage pins. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.