GRAUPNER MC 15 ANLEITUNG PDF
Graupner: MC, MC, MC, MC, MC, MC, MC, MC/20, es in Übereinstimmung mit dieser Anleitung mit vorgeschriebenr Spannung. Bowdenzuginnenrohr auf 15mm ab und kleben diese mit Sekundenkleber in den passen Sie den Ausschlag über den Sender an (Computersender der mc. Thank you very much for purchasing the Graupner mc HoTT .. 15 / _jh_V1_de. PC COM Port connection. Through this socket it is also possible to.
|Published (Last):||22 April 2006|
|PDF File Size:||6.85 Mb|
|ePub File Size:||9.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
The selection must be made before re- of modulation. All 8 switches have a functions by using 2 channels to make central position, which makes it 8 channels.
Table of Contents Add to my manuals Add. Page General Permissions Transmitter and Receiver for the 27 and 40 MHz bands are registered and can be used without charge.
Page 45 Fixed Wing Models Throttle Curve Throttle Curve Throttle Curve Low, Middle, High access via Set-Up Menu Three different profiles for the carburettor response Setting can be adjusted and called up in flight by external After selection of the point required using the switches; the function of the throttle pre-select is button and operation of the appropriate CH SEL included in this changeover.
Described on page The extremely high contrast enables, even with bright sunlight, a precise check of the functions displayed in the transmitter display such as operating voltage, input data, mixer functions, settings, direction of rotation, trim and programming This manual also for: Setting mix proportion and mix direction. As a matter fact I don’t need them.
GRAUPNER mc-16 Programming Manual
Page 65 Connections to the receiver Ch 1 to 8 The servos must be connected to the receiver outputs as shown below: Also included is a anleituung made mixer for Elevator Flap mixing. Mybe I’m not so skiled with internet. Manual in English for MC If I could find wit a long or flat arm wheel be nice. Page 90 The error message is cleared by pressing any key.
Page 70 Throttle and Collective Pitch anleitunt In Dutch I think. So, I will get the switch and trim the lever down so I can slip a brass tube over it. It can be used, however, for other similar models.
Page 24 Example 2: Page 97 This is fitted next to the receiver. Those picture I post it only as a referencenot to buy exactly. Operating Instructions Changes of the HF channels: I have an MC19s. I upgraded my MC with 4 3-way switches: Page of Go. Newly developed LCD multi-data display with integrated static driver for fraupner, clear digital display.
Throttle Curve Throttle Curve Low, Middle, High access via Set-Up Anlektung Three different profiles for the carburettor response Setting can be adjusted and called up in flight by external After selection of the point required using the switches; the function of the throttle pre-select is button and operation of the appropriate CH SEL included in this changeover.
Graupner Mc 15 Bedienungsanleitung Huawei
Is gonna be used for an RC submarine project. If the System Menu is active, press twice. All connectors are 2. I thought maybe was made only pieces and nobody cares to put on internet some info.
For models with a V-tail, “VTL”, must be used to mix the functions of elevator and rudder. Don’t show me this message again. Was the only one I get afford to buy. Yes is a very “common” language Three curves are available for button and operation of the appropriate CH SEL normal flight under motor powerand a separate For Delta models, “DLT” combines the functions of Ailerons and Elevators, where the servos are connected to receiver outputs grauupner and ,c Throttle anlditung 1, Rudder to 4.
Many Thanks in Advance. Receiver outputs 5 and 8 are available for auxiliary functions, e. Elevator Pitch Dual-Rate and Exponential for: Pitch Curve Pitch Curve Low, Middle, High access via Set-Up Menu Four different profiles for the collective pitch Setting response can be adjusted and called up in flight by After selection of the point required anlejtung the external switches.
Select the standard Since these are not influenced by the dual rate and You have concluded the basic programming of the model type “FL” in the system menu. Yes You are right and it’s a good idea. The MC can freely assign each input to any of up to 12 channels.
GRAUPNER MC / 40MHz – RC Groups
Aileron Roll Dual-Rate and Exponential for: Set-Up Menu General notes if necessary also over Ailerons. Beside two aileron servos, it is intended that two separate flap servos are used.
So if You have some directions for me don’t hesitate to tell me.
The switching function, described in 2.